SeaMaker 20 Gallon per Hour Water Maker Model and Pricing

                     Model   Fresh Water Production GPH/GPD  High Pressure Pump Amps 
    120/220V AC
    Boost Pump 
    SM20  20/480 9.3/4.8 8.2 $4395
     SM20-50Hz 20/480  6.8 (208-240v) 8.2  $4495 

    Module 1: High Pressure Pump and Motor Assembly
    One General Pump Company triplex plunger pump with a 316 stainless steel manifold and wetted parts, solid ceramic plungers and an anodized aluminum crankcase mechanically coupled to a 1.0Hp 120/220VAC electric motor.  Fitted with a pressure relief valve preset to 950 PSI.  

    Module 2: RO Pressure Vessel Assembly
    One filament wound fiberglass/epoxy pressure vessel.
    One SW30-2540 Dow Filmtec Polyamide thin-film composite high salt rejection RO Membrane (The Gold Standard in RO Membranes, not a discount off brand)
    Two fiberglass clamps affixed to fiberglass mounting feet.
    One 3ft long 3/8" high pressure braided stainless steel silicone covered hose for connecting the high pressure pump outlet to the RO pressure vessel.  (Longer hose available upon request for an additional charge)
    Module 3: Pre-filter and Boost Pump Assembly
    Two 10” clear filter housings with mounting bracket
    One 20 micron pre-filter element
    One 5 micron pre-filter element
    One self-priming 12V DC Jabsco boost pump
    (Also available in 120V AC, 208-240V AC, and 24V DC for an additional $100 Charge)

    Module 4: Valving and Cleaning Assembly
    One clear filter housing with mounting bracket
    One activated carbon filter element
    Two 3-way valves for selecting modes of operation:
    1) Normal operation of inlet seawater
    2) Fresh water flushing from ships tanks
    3) Pickling solution from 5 gallon bucket

    Module 5
    : Remote Control Panel 
    (Not included with the SeaMaker Simple units -S)
    An anodized aluminum panel with the following system controls:
    One 0-1 GPM flow meter
    One 0-1500 system pressure gauge
    One product water selector 3-way valve
    One stainless steel pressure regulating needle valve
    One 12V DC boost pump electrical switch
    One 120V AC high pressure pump electrical switch
    One boost Pump pressure gauge
    One boost pump regulating needle valve
    One 5ft 3/8" high pressure braided stainless steel silicon coated hose
    (Longer hose available upon request for an additional charge)

    Miscellaneous Included Equipment & Supplies:
    30ft of green 1/2" Polyethylene sea water tubing
    30ft of blue 1/4" Polyethylene product water tubing
    30ft of red 1/4" Polyethylene brine water tubing
    20ft of black 3/8" Polyethylene bypass water tubing
    10ft of Orange 3/8" Polyethylene pickling water tubing
    One cutter for the water tubing
    One spacing tool for proper insertion and removal of water tubing into push connector
    One 1/2" male NPT to push connector fitting for connecting to your seawater inlet source
    One 1/2" male NPT to push connector fitting for connecting to your ships water system for fresh water flushing of the water maker
    Three 1/4" male NPT to push connector fittings for connecting the brine, product water, and sample water outlet lines to your ships plumbing
    Locking clips for all push connector fittings
    Electronic copy of the Installation, Operation and Maintenance manual via USB Stick
    (Hard Copy available at our cost of $23)
    One filter housing wrench for filter element replacement
    5 pounds of pickling reagent
    One hand-held TDS meter for checking water quality
    Four spare 1/2" male NPT 90° elbow to push connector fitting if needed to replace the straight fittings which are pre-mounted on the modules for making the system plumbing easier
    An assortment of push-to-connect fittings to aid in installation

    What we Don't Provide. In other words, what you will need to supply:
    I made a YouTube Video going over the details and you can watch that
    YouTube Video Link
    In summary:
    Raw water through hull
    Raw water sea strainer (we recommend one like this)
    Electrical installation wire and breakers for the AC and DC Pumps
    Mounting screws and bolts for the individual system Modules
    Zip ties and mounting straps for securing the electrical and water lines
    That's it!  Everything else we provide with the with the water maker.

    Water Maker Module Sizes:
    The below table provides the length, width, height, and weight of the various water maker modules.  The listed dimensions represent the greatest size measurement to create a box that the module can be contained within. However, as can be seen in the module photo images, the modules could actually fit into a smaller space depending upon the installation orientation.

          Module    Length
     1: Pump and Motor 19  11  9 44
     2: RO Pressure Vessel   44
    6.5   14  
     3: Prefilter Assembly
      3: 12V DC Boost Pump
     9.5 5
      4: Valving and Cleaning Assembly 
     5  14.5  5
       5: Remote Control Panel  5
    11  11.25   4
    Automatic Fresh Water Flush ($595)
      Valving & Cleaning Panel ($350)



    * Please notify us if you plan a 220VAC installation so we can change the standard 120VAC electrical switch in your remote panel.
    * Standard Boost pump is a 12VDC self-priming pump. 
      (Here is a link to a Video we made explaining why we like the 12V DC pump)
    * A 120VAC Boost pump option available using 1.5Amp $100 Adder

    * A 208-240VAC Boost pump option available using 0.75Amp $100 Adder
    * A 24VDC Boost pump is available using 6.5Amp $100 Adder
    To request a copy of the SeaMaker 20 water maker manual with technical specifications along with detailed installation and operation
    Or Call, Text, or Skype Rich 7 Days-A-Week
    to talk all things water makers.
    Phone: 619-609-3432
    Skype Username: CruiseROWater

    Module 1
    Pump and Motor Assembly

    Module 2
    RO Pressure Vessel and Membrane
    with Fiberglass Mounting Clamps and Feet

    Module 3
    Standard 12V DC Self Priming Boost Pump
    (Also Available in 24V DC, 120V AC, and 208/240V AC
    for additional $100)

    Module 3
    Prefilter Assembly
    with 20 and 5 micron Prefilters

    Module 4
    Valving and Cleaning Assembly

    Module 5
    Standard Remote Panel

    Cruising Consumable Kit
    With a Year Supply of Consumables for $180

    Valving and Cleaning Panel
    Replacing the two 3-Way Valves Mounted on the Valving and Cleaning Assembly ($350)

    Script embedded in HTML